Chain Link Fencing Basics - Part 3: Fittings

Chain Link Fittings

 

Tension Wire

 

Tension wire is often used in place of bottom rail. Depending on the total linear footage of the fence, using tension wire can be a less expensive alternative than rails

Tension wire is also sometimes used in place of top rail in security applications because it makes the fence more difficult to climb. When using tension wire in place of top rail, a brace and truss setup is typically installed to keep the terminal posts from pulling over.

Smooth tension wire / utility wire has a wide number of uses, including residential fencing. It is typically available in 9, 11, 12, and 12.5 gauges. The most common use is in place of bottom rail on chain link fences.

Marcelled tension wire, which is usually 7 gauge, is used in commercial and industrial fencing applications. Due to the heavy gauge, Marcelled tension wire has crimps, or kinks, in it to facilitate stretching; without the crimps, stretching the 7 gauge wire over the length of the fence would be very difficult.

Line Fittings

Loop Caps

Loop caps fit on your line posts and secure the top rail of the fence. They are designed so that the top rail passes through them in a continuous line. Loop caps have 2 important dimensions, the post cap dimension (i.e. 2” for a 2” Post), and the top rail loop dimension (i.e. 1 3/8” for a 1 3/8” top rail)

Barb Arms 

Barb arms, like loop caps fit over the top of your line posts and have a hole in them to allow the top rail to pass through. Barb arms are available in 2 types, 3-wire and 6-wire. 3-Wire arms have 3 “Z” cuts or notches in them to hold 3 strands of barbwire. 6-wire arms have a V shape with 3 “Z” cuts on each side.

Line Rail Clamps 

Line Rail Clamps are used to secure mid-brace rails and bottom rails to your line posts. They are sold in 2 pieces, and are assembled around the post and attached using a carriage bolt & nut.

Terminal Fittings

Tension Bands

Tension bands are used in combination with tension bars to secure the stretched chain link fabric to a terminal post. The bands are placed around the terminal post, and hold the tension bar in place with a carriage bolt. There are two types of tension bands, flat and beveled. Flat bands are lighter, have flat edges, and are typically used for residential fencing applications. Beveled bands, on the other hand, are typically heavier with a thicker zinc coating, have a beveled edge, and are used in commercial projects.

Tension Bars

Tension bars are flat steel extrusions, usually 5/8” or ¾” thick, which are used to hold the stretched wire fabric in place at the terminal post. The tension bar is held in place by tension bands spaced every 12” apart on the terminal post.

Brace Bands

Brace bands are used to connect other fittings like rail ends, tension wire, and barbwire to your terminal posts. Like tension bands, brace bands come in flat and beveled varieties.

Rail Ends

Rail ends secure top, mid, and bottom rails to your terminal posts. They are held on to the terminal post with a brace band and 1 ¼” x 5/16” carriage bolt. Rail ends are typically available in aluminum (residential grade) and pressed steel (commercial grade). Commercial grade rail ends are often combo rail ends, which have a hole in them to insert a bent truss rod in a brace and truss setup.

Post Caps

Post caps fit over the top of your chain link posts to keep water and insects out. They fit over the outside of your post, so a 2" cap will fit on the outside of a 2" (1 7/8" O.D.) post.  In most situations, you will only use post caps on your terminal posts because loop caps will be used on your line posts to hold your top rail.   Post caps are generally available in aluminum and pressed steel, in 2 different styles, acorn and dome.

Chain Link Fencing Basics - Part 2: Framework

Framework is the tubular steel pipe that makes up the posts and rails of a chain link fence; it is available in a wide array of diameters and wall thicknesses.

When talking about the diameter of a fence post, there are a few important things to know.  First , similar to dimensional wood products, steel posts and fittings are usually labeled in nominal sizes; so, for example, a fence post listed as 2” is actually 1 7/8” O.D., and a fitting listed as 2" is meant to fit a 1 7/8" O.D. pipe.  Second, fence pipe is measured in outside diameter (O.D.); so, if you see that a post is 1 7/8”, it means that the diameter of the outer wall of the post is 1 7/8”, unless stated otherwise.

The strength of a tubular steel fence post is primarily a function of its wall thickness. There are a wide number of residential, commercial, and industrial grade pipe choices available. Different manufacturers have different brand designations for their pipe. For example, Allied Tube & Conduit designates its fence pipe as follows:

SS15 – Residential, Light Commercial – Wall Thickness on a 1 7/8” Pipe = .072”
SS20 – Commercial – Wall Thickness on a 1 7/8” Pipe = .090”
SS40 – Commercial/Industrial – Wall Thickness on a 1 7/8” Pipe = .120”

Also common in industrial fence applications is Schedule 40, also known as Standard Weight, pipe, which is a national standard size and has a wall thickness of .145”

Chain Link Posts

The size of the fence post that you use will be determined by a number of factors, including: the height of the fence, the gauge of the fabric, and the primary use of the fence. For example, a 4’ or 5’ residential fence with 11 gauge wire can usually be installed with 1 5/8” diameter line posts and 2” terminals. On the other hand, an 8’ commercial grade fence with 9 gauge wire will require line posts that are at least 2 ½” in diameter and terminal posts that are at least 3”. A general rule of thumb is that your terminal posts should be at least 1 size larger than your line posts.

Another factor to consider in choosing your posts is whether you will be using some type of privacy screening on the fence, either now or in the future. Privacy screening, slats, and fence weave products all add surface area to the fence, thereby increasing the wind load on the fence. You will typically have to increase your post sizes when using such products. So, on the 8’ commercial fence in the example above, you may need to switch to 3” line posts and 4” terminal posts. Depending on the estimated wind load on your fence, you may also have to adjust your posts wall thickness, spacing, and footer size/depth. A thorough discussion of wind load is beyond the scope of this introductory article. For more comprehensive information, view the Chain Link Fence Manufacturer’s Institute’s Wind Load Guide.

Chain Link Rails

Almost all permanent chain link fences have a top rail to support the weight of the chain link fabric and keep it from sagging over time. The fabric is tied to the rail using wire ties, which keeps the fence tight and prevents the fabric from being pushed down for easy ingress onto the property – either by an animal or trespasser.

Top rails are typically sold in 21’ sections (though they may be cut shorter for transportation purposes), and are either swedged* end or are sold with sleeves that can be used to splice the rails into one continuous rail. The top rail attaches to the terminal (end or corner) posts via rail ends, and runs through loop caps on the line posts.

*A swedged rail is tapered at one end so that it fits into the unswedged end of another rail, enabling you to create one long continuous rail.

A bottom rail serves the same purpose as the top rail – preventing the fabric from being pushed inward, thereby allowing easy access. Unlike top rail, however, bottom rail does not run in a continuous line; it must be cut down to fit between each section of fence. It attaches to the terminal post with an end cap, and line posts with line rail clamps. Many homeowners / fence installers choose to forgo the bottom rail in favor of bottom tension wire, which serves the same purpose, but is a less expensive alternative.

Often, chain link fences taller than 6’ also have a mid-brace rail, at least on each section between a terminal post and line post. The mid-brace rail provides support for the terminal post against the tension of the stretched wire fabric. In other words, it helps to keep the terminal post from being pulled over due to the high tension needed to keep the stretched fabric taut.

The typical diameters for top rail are 1 3/8” O.D. for residential installations and 1 5/8” O.D. for commercial installations, and most fittings are available for both sizes.

Chain Link Fencing Basics - Part 1: Wire Fabric

Fabric is what puts the “chain link” in chain link fence; it is created by a machine that weaves together 2 strands of metal wire into a mesh. A typical chain link mesh will have a diamond size (measured on the diagonals) of 2” or 2 ¼”, although smaller diamond sizes of 1 ¾” and 1 ¼” are also common. In fact, most chain link pool fences are constructed of 1 ¼” mesh to meet ICC pool codes because the smaller diamond size makes the fence more difficult to climb (Note: regulations do vary by municipality, so check with your local building department before buying your materials).

If you want to see how chain link is created, from the strand to the roll, check out this video on YouTube

The diameter of the wire strand is what determines the gauge of the chain link. It is a little counter-intuitive, but the higher the gauge, the thinner the wire; so, for example, 9 gauge galvanized chain link fabric is made from wire strand that is .148” in diameter, while 12 gauge galvanized chain link fabric is made from wire strand that is only .106” in diameter.

Most galvanized residential chain link fences use wire fabric that is 11 or 11 1/2 gauge, whereas most commercial fences use 9 gauge wire fabric. 6 gauge fabric can also be used, however it is very heavy and hard to stretch, so it is usually reserved for only heavy industrial and high security applications. On the flip side, 12 gauge and 12 ½ gauge wires are very thin, and are typically used for temporary fencing applications.

Here Kitty Kitty. A Recent Study Suggests Cats Kill Up to 18 Billion Small Creatures Per Year! Can Putting Up A Fence Keep Them In (Or Out Of) Your Yard?

A recent study from the Smithsonian Conservation Biology Institute suggests that cats kill up to 3.7 billion birds and 15 billion small mammals per year.  For some people, that may come as welcome news, as their thinking is that the cats are killing common pests like mice and rats.  Not true.  According to Pete Marra, an animal ecologist and a member of the team that conducted the study, the majority of the mammals that are killed are native woodland creatures like voles and chipmunks.  And while pet cats do play a role, feral cats bear most of the responsibility.

Often cat owners will let their cats come and go from the house as they please, knowing that the cat will return.  Aside from the danger of getting hurt by larger animals or other feral cats, letting your cat roam can increase the likelihood that they are off hunting.  If the last thing that you want to see is Snowball returning home with a dead bluejay or chipmunk, then you need some way to contain it to your yard and keep other animals out.  But is there any kind of fence can keep a cat in?  Can't they just climb, dig, or jump whatever obstacle you put in their way?  After all, cats have a strong natural instinct to hunt, and will go to just about any lengths to fulfill that desire.

The truth is, after much debate and discussion, the general consensus in our office is that no fence can 100% keep a cat in and that best way to ensure that your cat doesn't leave the yard is to keep them in the house.  But, we'll stay on the case and keep researching until we find the best method.  In the meantime, we would love to hear what our readers think.  If any of you have successfully contained your cat in your yard, leave us a comment to let us know how you did it.

Free Shipping on Hundreds of Fence and Railing Supplies

As part of a new pilot program, when you see the logo above on an item in our store, that item qualifies for free standard shipping on any order over $250.

Almost all of the new tools, paints, and solar lighting supplies in the store qualify.  As do most of our ornamental gate hinges and latches.  And the really big news is that Westbury Railing qualifies for free shipping, in some cases with the order of just one section. 

Fence Tools Now Available

Whether you're a weekend warrior or a professional contractor, installing a fence requires the right tools for the job.  That's why over the past few weeks we've been adding a large variety of professional quality fencing tools; everything from fencer's pliers to string.  Take a look at just a small sample of the items below.  When you click on the link, it will take you directly to the section of the site where the tools are. 

Measuring Tools - Tapes, Rollers, Levels, & More.

Cutting Tools - Hacksaws, Bolt Cutters

Stretching Tools - Wire Grips, Come-A-Longs, Ratchets

Digging Tools - Post Hole Diggers, Augur Bits

Specialty Fence Tools - Hog Ring Pliers, Gate Clip Bending Tools, Barricade Tape

Paints & Coatings - Cold Galvanizing Spray, Touch Up Paints

Tension Wire & Barbed Wire Now Available

We forgot to mention yesterday that our new chain link wire category also includes galvanized barb wire, razor wire, tension wire, and utility wire.  We also sell all of those items in vinyl coated varieties, which will be coming soon to the store.  All of the above types of wire are eligible for the same quantity discounts as our chain link fabric.